Garburator installation

Some cast sinks will require putty. If no putty is used, insert the sink flange through the rubber gasket, into the sink opening. Do not turn the flange once it is sealed. Insert the flange into the sink opening, press down hard to squeeze out excess putty.

From under the sink, trim off excess putty flush with the bottom edge of the sink opening. With arrows pointing up, screw the support ring onto the sink flange and hand tighten until the sink flange will not move. At this point you may want to insert the stopper before running a test to determine if you have a leak under the kitchen sink, place a plastic box, you may also use a flashlight to better your vision in the sink and fill with water to check the sink flange seal and insure there are no leaks.

Make sure the groove on the inside of the cushion mount fits over the lip on the sink flange, similar to putting the lid on a plastic container. Run your fingers around the entire cushion mount with slight pressure. Do not press too hard. When the cushion mount is properly sealed, the mount ring can be pulled downward over the cushion mount and will be free to turn. Before install garburator hopper projection to cushion mount and tight with mount ring you have to done: Dishwasher connection if required : If you are connecting to a dishwasher, you must remove knock-out plug from garburator inlet.

Using a blunt instrument wooden dowel or steel punch knock out entire plug. When knockout plug falls into garburator, you may remove it.

Attaching the discharge elbow: Connect the discharge elbow to the garburator, use elbow gasket, elbow flange and tight with two screws. On the elbow first put metal or plastic nut, and after that a soft plastic gasket. Connect electricity: First you must disconnect the power supply. Between white wire and black wire the voltage is V AC. Ground wire should be attached to the ground screw in the bottom of the garburator end bell.

To wire your garburator directly into the house current. Grounding instruction: This garburator, must be grounded to reduce the risk of electric shock. This garburator must be connected to a grounded, metal, permanent wiring system; or an equipment-grounding conductor must be run with the circuit conductors and connected to the grounding terminal or lead on the appliance garburator. If you use BX cable — technically known as armored cable insulated electrical wires protected by a flexible aluminum or steel covering : — Install the cable connector in the hole.

If BX cable is not used, provide a separate ground wire to nearest reliable ground, using the screw in the end bell for the ground wire. Attach a copper wire securely to garburator ground screw and attach other and of wire to a reliable ground. Use only CSA approved ground clamp. If plastic pipe is used in your home, a qualified technician should install a proper ground. CSA — Every electrical device or component must be certified by the Canadian Standards Association or recognized equivalent before it can be sold in Canada.

Now if you installed sink flange to the sink, if you removed knock-out plug from dishwasher inlet if required , if you connected discharge elbow with plastic nut and soft plastic gasket, if you installed ground and electric wires you can put discharge elbow to the outlet plumbing pipe and attach to the sink flange garburator.

Attach to the sink flange garburator: — Line up the garburator when elbow is in side outlet pipe under the sink flange. Guide the hopper projections the top of the garburator into the mount ring slots.

Lock mount ring: Turn the mount ring to the right until it lock up tight. Hopper projections the top of the garburator must be to the extreme left of the mounting slot. If the mount ring is hard to turn, you may add a small amount of liquid soap to the hopper projections located on the top of the garburator small square on left and right side. Now you can slide down on discharge elbow soft plastic gasket and tight clockwise with plastic nut to the outlet plumbing pipe.

Connect hose: Connect the dishwasher hose using a universal hose clamp. If the hose size is different, you will need a stepped rubber adapter. Make sure all plumbing connections are tight.

Before running a test to determine if you have a leak under the kitchen sink, place a plastic box, you may also use a flashlight to better your vision. Read all instructions and safety precautions before using the Garburator. Stoper 2. Splash guard 3. Electrical cords may not be available with the Garburator and may be sold separately. Test your connections by placing the stopper into the sink drain and filling the sink with water. Check for leaks. Plug in the disposal, and turn on the power.

A mismatch or error in any one of the above steps could lead to irreversible damage to the equipment which may warrant purchasing of a new Garburator all together. It is generally never a good idea to try and install a Garburator on your own unless you have experience as a plumber.

The cost of having to repair potential breakdowns due to a faulty installation or the cost of having to replace it all together far outweigh any savings you may have in the process of a DIY installation. Best Garburator Repair Calgary Plumbers. If you live in Calgary or any of their surrounding areas then you can reach out to us at Urban Piping and we will provide you with an immediate, low-cost, and professional installation of your Garburator.

Look us up on Google and you will find that we have hundreds of 5- star reviews by our customers who are supremely satisfied with our service. All of our services in the area of plumbing are licensed, bonded and insured. So, if you are ever in need of a Garburator installation, reach out to the professionals and we will take the trouble off your hands.

How to Install a Garburator. So, what exactly is a Garburator? Garburators and Their Positive Effects on Drains Breaking Hollywood Garburator Myths The vast majority of scary movies portray a Garburator a being an instrument with rotating blades but this is far from the truth.

Step 3: Prepare the New Garburator Underneath the sink, stack the fiber gasket, backup flange, and mounting ring, and slide onto the underside of the flange. Step 4: Connect to Dishwasher Drain To connect to the dishwasher drain, use a hammer to knock out and remove the drain plug from the inlet on the disposal.

Step 6: Test Connections Test your connections by placing the stopper into the sink drain and filling the sink with water. Best Garburator Repair Calgary Plumbers If you live in Calgary or any of their surrounding areas then you can reach out to us at Urban Piping and we will provide you with an immediate, low-cost, and professional installation of your Garburator. Published On: November 6th, Categories: Garburators Tags: garburator install , garburator repair , waste disposal.

Related Posts. How to Use a Garburator? Waste Disposal Units — Top Brands. Plumbing Topics. Send Me The Free Guide! Your email is kept private between us and we do not send spam email.

Calgary Office. Edmonton Office. Vancouver Office. Follow Us. Ask Us About Plumbing.