Record the model and serial numbers of your machine. Previous Page. Next Page. It provides instructions on safe installation, use, and maintenance. Retain it for future reference. Record the model and serial numbers of your machine and report this information to your dealer if your machine requires service. Tilted Drum and Extra Large Door Opening Tilted drum and extra large opening make it possible to load and unload clothing more easily.
Water Circulation Spray detergent solution and water onto the load over and over. Page 5 Install or store unit where it will not be exposed to temperatures below freezing or exposed to outside weather conditions. Properly ground washer to conform with all governing codes and ordinances. To reduce the risk of electric shock, do not install the washer in humid spaces. The base opening must not be obstructed by carpeting when the washing machine is installed on a carpeted floor.
Laundry tub Hose Retainer max. Install the appliance on a solid and level floor surface, preferably in a corner of the room. Fabric Care Labels Look for a care label on your clothes. This will tell you about the fabric content of your garment and how it should be washed. Page 11 The automatic dispenser consists of four compartments which hold 1 liquid chlorine bleach, 2 liquid fabric softener, 3 liquid or powdered detergent for prewash and 4 liquid or powdered detergent and color safe bleach for main wash.
All laundry products can be added at once in their respective dispenser compartments. They will be dispensed at the appropriate time for most effective cleaning.
Page 12 2. Main Wash Detergent Compartment 3. Detergent is flushed from the compartment. The bleach will be automatically dispenser at the beginning of the cycle.
Either dispensed at the proper time during the wash cycle. Drain trouble Visit to service. Recommend to reduce the amount of detergent. Page Fault Diagnosis And Troubleshooting Be careful of electric shock if disconnecting parts while troubleshooting.
First of all, check the connection of each electrical terminal with the wiring diagram. Is the washer installed on a solidly constructed Move the washer or floor? Check if the washer is perfectly level as follows: Check the leveling of the washer with a Level and check that the washer is stable. Page 24 If it still has severe vibration and noise, regulate a specific spin speed that generates excessive vibration and noise as follows: 1 Put an unbalance part rubber inside of the drum.
Is the tap opened? Open the tap. Is the inlet valve filter clogged? Clean the filter. Remove foreign material. Hose Connector Hose White Remove foreign material.
Reconnect or repair Is the connector disconnected, disassembled? Is the resistance of thermistors on dry duct FRC : 2.
Page Disassembly Instructions 9. Pull the top plate backward and upward as shown. Remove the Protect Cover. Unscrew 1 screw on the back. Disassemble the Main PWB.
Page 35 Disassemble the top plate assembly. Pull out the drawer. Unscrew the nut at the lower part of the dispenser. Disassemble the 4 connectors from the valves. Unscrew the screw from filter cover. Put a flat - screwdriver or putty knife into the both sides of the filter cover, and pull it out. Unscrew the screw from the lower side of the cabinet cover. Page 37 Open the door. Disassemble the clamp assembly. Tilt the cabinet cover. Disconnect the door switch connector.
Lift and separate the cabinet cover. Disassemble the Gasket. Page 38 Open the door. Put a flat - screwdriver into the openng of the hinge, and pull out the hinge cover. Unscrew a screw from the lower side of door. Disassemble the door upward. Be careful! The door is heavy. Page 39 Disassemble the cabinet cover. Separate the pump hose, the bellows and the circulation hose assembly from the pump assembly. Disassemble the pump assembly in arrow direction. Disassemble the cabinet cover.
Separate 2 connectors from the heater. Loosen the nut and pull out the heater. Page 40 Disassemble the cabinet cover. Separate the heater from the tub. Remove any foreign objects wire, coin, etc. Unscrew the 4 screws from the back cover. Unscrew the single screw from the lower-right side of the cabinet.
Page 41 Disassemble the back cover.
0コメント